Champtek IG-300 Especificaciones

IG-300 2DImagerBarcodeScannerUser’sManual

5. Operating Settings 5.1 Scanning Triggering <Level> A reading session begins (lighting and decode processing on) when beam is activated an

Autostand This mode allows you to switch from Flashing trigger mode to Level trigger mode. Autostand begins in flashing mode: At power up the lig

5.2 Time Out <2 sec> 4 sec 6 sec 5.3 Good Read Mode When active, the scan engine stops the reading session after a successful de

5.4.2 Good Read Beeps <One Beep> Two Beeps None 5.4.3 Beep Duration 60 msec <80 msec> 200 msec Off 5.4.4 Timing <

5.5 Good Read Duration 5.5.1 Good Read Led Duration <80 msec> 0.5 sec 1 sec Off 5.5.2 Error Beep <On> Off 5.5.3 Setup Be

5.6 Bad Read Message Settings <Default = "NOREAD"> Active <Not Active > 13

6. Imager Settings 6.1 Imager Mode You can set the best reading performance depends on the environment, your used application and type of barcodes. •

6.2 Firmware Version Display the firmware version of the scanner, please scan below barcode. Engine Firmware Version Scanner Decoder Firmware V

7. Programming Codes 7.1 Factory Default The factory default settings are shown with bold < > in the following pages. To set the scanner

7.2 RS232 Parameters Baud Rate 1200 2400 4800 9600 <19200> 38400 7.2.1 Data Bits Data Bits 7 <Data Bits 8> 7.2.2 Stop Bit

Contents 1.Introduction ... 1 1.1 Safety&Caution...

7.2.3 Parity <None> Even Odd Mark Space 7.2.4 Handshaking RTS/CTS Enable

7.2.5 Keyboard Wedge Mode Parameter 1) Terminal Type <IBM PC/AT,PS/2> IBM PC/XT IBM PS/2 25, 30 2) Capslock Detection Enable <Disable

4) Send Character by ALT Method Enable <Disable> 5) Select Numerical Pad ON <OFF> 6) Time out Between Characters <0 ms> 5 m

7) Language Selection <US English> UK English Italian Spanish French German Swedish Switzerland Hungarian Japanese 21

Belgium Portuguese Denmark Netherlands Turkey Reserved 1 22

7.3 Decoding Selection 7.3.1 Symbologies Selection Australian Post ON <Australian Post OFF> AZTEC ON <AZTEC OFF> BPO ON <BPO O

<Codablock A OFF > Codablock F ON <Codablock F OFF > CODE 11 ON <CODE 11 OFF> <CODE 39 ON> CODE 39 OFF CODE 93 ON

GS1-128 OFF <DATAMATRIX ON> DATAMATRIX OFF DATAMATRIX‐MIRRORON<DATAMATRIX‐MIRROROFF>Dutch Post ON <Dutch Post OFF>

26 <EAN 128 ON> EAN 128 OFF GS1 CC-A/B ON <GS1 CC-A/B OFF> GS1 CC-C ON <GS1 CC-C OFF> GS1 DataBar-Omni ON <GS1 DataBar O

Infomail ON <Infomail OFF> Interleaved 2 of 5 ON <Interleaved 2 of 5 OFF> Japan Post ON <Japan Post OFF> Matrix 2 of 5 ON &l

1 1. Introduction Thank you for purchasing this brand-new designed 2D imager hand held barcode scanner. This is a cutting-edge gun-type Area Imag

MSI ON <MSI OFF> <PDF417 ON> PDF417 OFF Planet ON <Planet OFF> PLESSEY ON <PLESSEY OFF> Postnet ON <Postnet OFF&

Standard 2 of 5 ON <Standard 2 of 5 OFF> Sweden Post ON <Sweden Post OFF> Telepen ON <Telepen OFF> TLC 39 ON <TLC 39 OFF&

7.3.2 Multi Code The multicode function is used configure the scanner to read a series of bar codes and then transmit them all at once. <Not a

7.3.3 Postambles The scanner can be programmed to output Barcode data according to the following format: [BAR CODE DATA] [POSTAMBLE STRING] Exam

Appendixes A. Decimal Value Table 0 1 2 3 4 5 6 7 8 9 32

B. ASCII Table 33 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

34 C. Readable Symbologies 1D Symbologies Symbologies ReadableDefaultEnableEAN/UPC○ ○UCC/EAN128○ ○ISBN○ISBT○Code11○Code39○ ○Code93

35 2D Symbologies Symbologies ReadableDefaultEnableDataMatrix ○ PDF417 ○ ○MicroPDF417 ○ MaxiCode ○ QRcode ○ Aztec ○ EAN.UCCcomposite○

36 D-3 Indicator LED Status Scanner Light Signal StatusGreen 1blinkand1beepgoodreadandtransmitted D-4 Electrical Characteristics Opera

E. Scan Map  Symbology DensityMinimumDistance(+/‐10%)MaximumDistance(+/‐10%)Code390.125mm 5.2cm 12.1cm0.20mm 2.0cm 21.5cm0.25m

12) If there are the following situations please contact with the qualified serviceman to check this equipment. 13) The damage of wire or pin of po

F. Test Symbologies Scan one or more of these barcodes to test barcode symbologies you enabled. Codabar Code 39 Code 93 Code 128 DataMatrix

39 PDF417 GS1 DataBar Omnidirectional GS1 DataBar Omni Stacked GS1 DataBar Expanded GS1DataBar Expanded Stacked GS1 DataBar Limited

Set factory default Engine Firmware Version Scanner Decoder Firmware Version Due to Champtek’s / Scantech ID’s contin

2. General Description 2.1 Product Description IG-300 is a high performance wire 2D imager barcode scanner supporting liner, area imager barcode sc

4 3. Installation 3.1 Unpacking 1) Take device and its accessories out of the box. 2) Remove the packing material. 3) Check the standard shi

3.3 USB Driver In case you will use the device with USB Virtual COM port emulation, please contact with your dealer and download the correct USB dri

6 4. Configuring 4.1 Preface How to configure this device: The Barcode Programming Feature gives the possibility to change the scanner settings w

7 4.3 Scanner Settings with Utility Tool Manufacturer has setup this scanner with the most common used programming codes, it could be possible tha